Dell Vostro 3490 Service Manual Download Page 84

Page: 84 / 96

System setup options

NOTE:

Depending on the and its installed devices, the items listed in this section may or may not appear.

General options

Table 2. General

Option

Description

System Information

Displays the following information:

•

System Information: Displays

BIOS Version, Service Tag, Asset Tag, Ownership Tag,

Ownership Date, Manufacture Date,

and the

Express Service Code

•

Memory Information: Displays

Memory Installed, Memory Available, Memory Speed,

Memory Channel Mode, Memory Technology, DIMM A size, and DIMM B size

•

Processor Information: Displays

Processor Type, Core Count, Processor ID, Current Clock

Speed, Minimum Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor
L3 Cache, HT Capable,

and

64-Bit Technology.

•

Device Information: Displays

Primary HDD, ODD Device, M.2 SATA SSD, M.2 PCIe SSD-0,

LOM MAC Address, Video Controller, Video BIOS Version, Video Memory, Panel type,
Native Resolution, Audio Controller, Wi-Fi Device, and Bluetooth Device.

Battery Information

Displays the battery status health and whether the AC adapter is installed.

Boot Sequence

Allows you to specify the order in which the computer attempts to find an operating system from
the devices specified in this list.

Advanced Boot Options

Allows you to select the Legacy Option ROMs option, when in UEFI boot mode. By default, no option
is selected.

•

Enable Legacy Option ROMs

•

Enable Attempt Legacy Boot

UEFI Boot Path Security

This option controls whether or not the system will prompt the user to enter the Admin password
when booting a UEFI boot path from the F12 Boot Menu.

•

Always, Except Internal HDD—Default

•

Always

•

Never

Date/Time

Allows you to set the date and time settings. Changes to the system date and time take effect
immediately.

System information

Table 3. System Configuration

Option

Description

Integrated NIC

Allows you to configure the on-board LAN controller.

•

Disabled = The internal LAN is off and not visible to the operating system.

•

Enabled = The internal LAN is enabled.

•

Enabled w/PXE = The internal LAN is enabled (with PXE boot) (selected by default)

SATA Operation

Allows you to configure the operating mode of the integrated hard drive controller.

•

Disabled = The SATA controllers are hidden

•

AHCI = SATA is configured for AHCI mode

•

RAID ON = SATA is configured to support RAID mode (selected by default)

System setup

Summary of Contents for Vostro 3490

































































































Search results

Summary of Contents for Vostro 3490

Reviews:

Related manuals for Vostro 3490

Brands by name

Popular brands

Dell Vostro 3490, Service Manual

Search results

Summary of Contents for Vostro 3490

Reviews:

Related manuals for Vostro 3490

Brands by name

Popular brands