Dell Studio One 19 Service Manual Download Page 45

Page: 45 / 53

Boot Sequence

This feature allows you to change the boot sequence for devices.

Boot Options

Processor L2 Cache

Displays the processor L2 cache size.

Memory Installed

Indicates the amount of installed memory in MB.

Memory Available

Indicates the amount of memory available in MB.

Memory Speed

Indicates the memory speed in MHz.

Standard CMOS Features

System Time

Displays current time in hh:mm:ss format.

System Date

Displays the current date in mm:dd:yy format.

AHCI Port0

Auto detects IDE devices in port 0.

AHCI Port1

Auto detects IDE devices in port 1.

Advanced BIOS Features

CPU Feature

Describes type of processor.

USB Device Setting

Enable or disable the USB controller /Set the operational USB speed.

Advanced Chipset Features

Onboard Audio Controller

Allows you to enable or disable the audio controller.

SATA Mode select

Allows you to switch between AHCI and IDE.

Onboard LAN Controller

Allows you to enable or disable onboard Broadcom network controller.

Onboard LAN Boot ROM

Allows you to enable or disable ROM for Broadcom PCI E Network Controller.

Boot Device Configuration

Boot Settings Configuration

Enable or disable fast boot and Numlock key.

Hard Disk Boot Priority

Sets the hard drive boot priority. The items displayed are dynamically updated according to the hard drives detected.

1st Boot Device

Specifies the boot sequence from the available devices.

Removable; CD/DVD; Hard Drive; Disabled (Removable by default).

2nd Boot Device

Specifies the boot sequence from the available devices.

Removable; CD/DVD; Hard Drive; Disabled (CD/DVD by default).

3rd Boot Device

Specifies the boot sequence from the available devices.

Removable; CD/DVD; Hard Drive; Disabled (CD/DVD by default).

Boot Other Device

Allows you to boot through any other device.

Power Management Features

ACPI Suspend Type

Specifies the suspend type. The default is S3.

C1E Support

This option allows you to enable or disable the "Enhanced Halt State".

Remote Wake Up

This option turns on the computer when a user tries to access the computer through the LAN. The default is Enabled.

AC Recovery

Auto Power On

Enables you to set an alarm to turn on the computer automatically. The default is Disabled.

BIOS Security Features

Supervisor Password

Status of supervisor password installed.

User Password

Status of user password installed.

Set Supervisor Password

Allows to set the desired supervisor password.

Exit

Exit Options

Provides options to

Load Optimal Default, Save and Exit Setup, and Exit Without Saving

Summary of Contents for Studio One 19






















































Search results

Summary of Contents for Studio One 19

Reviews:

Related manuals for Studio One 19

Brands by name

Popular brands

Dell Studio One 19, Service Manual

Search results

Summary of Contents for Studio One 19

Reviews:

Related manuals for Studio One 19

Brands by name

Popular brands