Dell S6100 Configuration Manual Download Page 1346 | Manualshive

Page: 1346 / 1743

background image

Remote Monitoring (RMON)

The Dell Networking OS remote monitoring (RMON) is implemented on the platform.
Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection. Dell
Networking OS RMON supports the following RMON groups, as defined in RFC-2819, RFC-3273, RFC-3434, and RFC-4502:

•

Ethernet Statistics Table; RFC-2819

•

Ethernet Statistics High-Capacity Table; RFC-3273, 64bits

•

Ethernet History Control Table; RFC-2819

•

Ethernet History Table; RFC-2819

•

Ethernet History High-Capacity Table; RFC-3273, 64bits

•

Alarm Table; RFC-2819

•

High-Capacity Alarm Table (64bits); RFC-3434, 64bits

•

Event Table; RFC-2819

•

Log Table; RFC-2819

•

User History; RFC-4502

•

Probe Configuration (Capabilities, SoftwareRev, HardwareRev, DateTime and ResetControl); RFC-4502

Dell Networking OS RMON does not support the following statistics:

•

etherStatsCollisions

•

etherHistoryCollisions

•

etherHistoryUtilization

NOTE:

Only SNMP GET/GETNEXT access is supported. Configure RMON using the RMON commands. Collected data is lost

during a chassis reboot.

Topics:

•

•

rmon collection history

•

rmon collection statistics

•

•

•

•

show rmon alarms

•

show rmon events

•

show rmon hc-alarm

•

show rmon history

•

•

show rmon statistics

44

1346

Remote Monitoring (RMON)

«
...
1344
1345
1346
1347
1348
...
»

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

Brand: Water Witch Pages: 2

Brand: E-Trailer Pages: 8

Brand: IDEC Pages: 5

Brand: IDEC Pages: 7

Brand: JB Systems Light Pages: 15

Brand: rako Pages: 4

Brand: DAITEM Pages: 37

Brand: Maiwe Pages: 5

Brand: hager Pages: 2

Brand: HIKVISION Pages: 25

Brand: Canoga Perkins Pages: 7

Brand: GarrettCom Pages: 77

Brand: WELLTECH Pages: 280

Allen-Bradley Guardmaster 440G-LZ

Brand: Rockwell Automation Pages: 40

Brand: Quark-Elec Pages: 10

Brand: Extron electronics Pages: 59

Brand: Tripp Lite Pages: 12

Tuffset 200302F

Brand: VXI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands