manualshive.com logo in svg

Dell S6000-ON, Installation Manual

Share
Download
Dell S6000-ON Installation Manual Download Page 3

Contents

1 About this guide............................................................................................................................................. 5

Information symbols...........................................................................................................................................................5
Related documents............................................................................................................................................................ 5

2 The S6000–ON system................................................................................................................................. 6

Introduction.........................................................................................................................................................................6
Features...............................................................................................................................................................................7
Physical dimensions........................................................................................................................................................... 7
Ports.................................................................................................................................................................................... 8
System status.....................................................................................................................................................................8
LED display..........................................................................................................................................................................8

LED behavior................................................................................................................................................................ 9

Prerequisite......................................................................................................................................................................... 9
Orderable S6000–ON components............................................................................................................................... 10

3 Site preparations...........................................................................................................................................11

Site selection......................................................................................................................................................................11
Cabinet placement............................................................................................................................................................ 11
Rack mounting.................................................................................................................................................................. 12
Grounding.......................................................................................................................................................................... 12
Fans and airflow................................................................................................................................................................12

Fan combinations........................................................................................................................................................12

Power................................................................................................................................................................................. 12
Storing components......................................................................................................................................................... 13

4 NEBS compliance.........................................................................................................................................14

Important information...................................................................................................................................................... 14

5 S6000–ON installation.................................................................................................................................15

Unpack the system...........................................................................................................................................................15

Unpacking Steps.........................................................................................................................................................15

Rack or cabinet hardware installation............................................................................................................................ 16

Rack mount safety considerations........................................................................................................................... 16
Dell ReadyRails installation.........................................................................................................................................16
Two-post flush-mount configuration........................................................................................................................17
Two-post center-mount configuration.....................................................................................................................18
Four-post threaded configuration.............................................................................................................................19
S6000-ON system installation................................................................................................................................. 20

Ground cable attachment............................................................................................................................................... 22
QSFP+ optic installation..................................................................................................................................................22

Remove the QSFP+ Optics...................................................................................................................................... 22

System power-up.............................................................................................................................................................22

Contents

3

Summary of Contents for S6000-ON










































Reviews:

No comments

Brands by name

Popular brands

Load more brands