manualshive.com logo in svg

Dell S6000-ON, Installation Manual

Share
Download
Dell S6000-ON Installation Manual Download Page 10

•

Copper/fiber cables

Other optional components are:

•

Additional power supply unit

•

Additional fan module

•

Additional mounting brackets (if installing in a four-post rack or cabinet)

Orderable S6000–ON components

You can order the S6000–ON system in several configurations. You can also order optional modules and optics separately.

•

S6000-ON AC Normal Airflow: thirty-two 40 Gbps QSFP+ ports, two AC power supplies, and three fan subsystems—airflow from the 

I/O side to the PSU side

•

S6000-ON AC Reverse Airflow: thirty-two 40 Gbps QSFP+ ports, two AC power supplies, and three fan subsystems—airflow from the 

PSU side to the I/O side

•

Fan with airflow from the I/O side to the PSU side

•

Fan with airflow from the PSU side to the I/O side

•

AC Power supply with airflow from the I/O side to the PSU side

•

AC Power supply with airflow from the PSU side to the I/O side

10

The S6000–ON system

Summary of Contents for S6000-ON










































Reviews:

No comments

Brands by name

Popular brands

Load more brands