manualshive.com logo in svg

Dell PowerEdge FD332, Owner'S Manual

Share
Download
Dell PowerEdge FD332 Owner'S Manual Download Page 5

About your Dell PowerEdge FD332

The Dell PowerEdge FD332 is a storage sled supported on the Dell PowerEdge FX2s enclosure. PowerEdge FD332 supports up to sixteen 
hot swap 2.5 inch hard drives/SSDs, and a storage controller module with single or dual controller modes.

Topics:

•

Terms used in this document

•

Front panel features and indicators—PowerEdge FD332

•

Hard drive/SSD indicators

•

Storage Controller Module indicators

•

Documentation matrix

•

Quick Resource Locator

Terms used in this document

The following table describes the terms used in this document.

Term

Description

Enclosure or chassis

Refers to the PowerEdge FX2s enclosure.

NOTE: 

PowerEdge FD332 is not supported on the 

PowerEdge FX2 enclosure.

Three-bay chassis

Refers to the PowerEdge FX2s enclosure configuration that 
supports one full-width and two half-width sleds.

Four-bay chassis

Refers to the PowerEdge FX2s enclosure configuration that 
supports four half-width sleds.

Six-bay chassis

Refers to the PowerEdge FX2s enclosure configuration that 
supports four quarter-width sleds and two half-width sleds.

Storage sled or system

Refers to PowerEdge FD332.

Compute sled

Refers to the half-width, quarter-width, or full-width sleds, to which 
the storage sled(s) may be mapped.

NOTE: 

The storage sled is not supported with the 

PowerEdge FM120x4 half-width compute sled.

Hot swap

A component is considered hot swap if it can be removed or 
installed while the sled is powered on.

Drive drawer

Refers to the hard drive/SSD drawer that can support up to 16 hot 
swap hard drives/SSDs.

PowerEdge RAID Controller (PERC)

Refers to the storage adapter(s) on the storage controller module.

PowerEdge HBA Controller (HBA)

Refers to the storage adapter(s) on the storage controller module.

1

About your Dell PowerEdge FD332

5

Summary of Contents for PowerEdge FD332















































Reviews:

No comments

Brands by name

Popular brands

Load more brands