Dell PowerConnect B-FCX Hardware Installation Manual Download Page 20

Page: 20 / 86

PowerConnect B-FCX Switch Hardware Installation Guide

53-1002267-01

Hardware features

FIGURE 12

Power status LEDs

TABLE 8

System status LEDs

LED

Condition

Status

PS1
PS2
(Power Supply
Status)

Green

Power supply is operating normally.

Amber

Power supply fault.

Off

Power off or failure.

Diag
(Diagnostic)

Flashing Green

System self-diagnostic test in progress.

Green

System self-diagnostic test successfully completed.

Amber

System self-diagnostic test has detected a fault. (Blower, thermal or any
interface fault.)

A or S
(Active or Standby)

Green

The device is the Active controller. If this LED is flashing green, the
system is initializing.

Amber

Indicates the device is the Standby controller.

Off

Device is operating as a stack member, or is in standalone mode.

Up Link or Down
Link (Stacking
uplink or downlink
port status)

Green

Uplink is operating normally.

Off

Uplink has failed or there is no link.

Stack ID (1-8)

Green

Indicates the device stack ID.

Power status LEDs

TABLE 9

Power status LEDs

LED

Condition

Status

DC OK

Green

DC output ok

Red DC

output

fail

AC OK

Green

AC input ok

Off

AC input fail

Summary of Contents for PowerConnect B-FCX























































































Search results

Summary of Contents for PowerConnect B-FCX

Reviews:

Related manuals for PowerConnect B-FCX

Brands by name

Popular brands

Dell PowerConnect B-FCX, Hardware Installation Manual

Search results

Summary of Contents for PowerConnect B-FCX

Reviews:

Related manuals for PowerConnect B-FCX

Brands by name

Popular brands