manualshive.com logo in svg

Dell P2422HE, User Manual

Share
Download
Dell P2422HE User Manual Download Page 77

Troubleshooting 

│

  77

No network 
connection

Network dropped or 
intermittent

• Do not turn Off the monitor during 

network connection.

The LAN port is 
not functioning

OS setting or cable 
connection issue

• Ensure that the latest BIOS and 

drivers for your computer are 
installed on your computer.

• Ensure that the RealTek Gigabit 

Ethernet Controller is installed in the 
Windows Device Manager.

• If  your  BIOS  Setup  has  a  LAN/GBE 

Enabled/Disabled option, make sure 
it is set to Enabled.

• Ensure that the Ethernet cable is 

connected securely on the monitor 
and the hub/router/firewall.

• Check the status LED of the Ethernet 

cable to confirm connectivity. Re-
connect both ends of the Ethernet 
cable if the LED is not lit.

• First power off the computer and 

unplug the USB Type-C cable and 
the power cord from the monitor. 
Then, power on the computer and 
plug the power cord and the USB 
Type-C cable into the monitor.

Summary of Contents for P2422HE

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands