manualshive.com logo in svg

Dell P2422HE, User Manual

Share
Download
Dell P2422HE User Manual Download Page 12

12 

│

  About your monitor

*To avoid signal interference, when a wireless USB device has been connected to a 
USB downstream port, it is NOT recommended to connect any other USB devices 
to the adjacent port(s).

7

USB Type-C upstream 
port

Connect the USB Type-C cable that came 
with your monitor to the computer. This port 
supports USB Power Delivery, Data, and 
DisplayPort video signal. The SuperSpeed 
USB 5 Gbps (USB 3.2 Gen1) Type-C port 
supports Alternate Mode DP1.2 with a 
maximum resolution of 1920 x 1080 at 60 Hz, 
PD 20 V/3.25 A, 15 V/3 A, 9 V/3 A, 5 V/3 A.

NOTE: 

USB Type-C is not supported on 

versions of Windows prior to Windows 10.

8

SuperSpeed USB 
5 Gbps (USB 3.2 Gen1) 
Type-A downstream 
port (4)

Connect your USB device.*

NOTE: 

To use these ports, you must 

connect the USB Type-C cable (shipped with 
your monitor) to the USB Type-C upstream 
port on the monitor and to your computer.

9

RJ45 port

Connect the Internet. You can surf Internet 
via RJ45 only after you have connected the 
USB Type-C cable (shipped with your 
monitor) from the computer to the monitor.

Summary of Contents for P2422HE

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands