Dell P2422HE User Manual Download Page 7

Page: 7 / 80

About your monitor

│

Product features

The

Dell P2422HE

P2722HE

monitor has an active matrix, Thin-Film Transistor

(TFT), Liquid Crystal Display (LCD) and LED backlight. The monitor features
include:

•

P2422HE

: 60.47 cm (23.80 in.) viewable area (measured diagonally).

1920 x 1080 (16:9) resolution, plus full-screen support for lower resolutions.

•

P2722HE

: 68.60 cm (27 in.) viewable area (measured diagonally).

1920 x 1080 (16:9) resolution, plus full-screen support for lower resolutions.

• Wide viewing angle to allow viewing from a sitting or standing position.

• Color gamut of sRGB 99%.

• Digital connectivity with DisplayPort, USB Type-C and HDMI.

Power cable (varies by
country)

DisplayPort to DisplayPort
cable (1.8 meters)

USB Type-C cable (1.8
meters)

Cable tie

• Quick Setup Guide

• Safety, Environmental,

and Regulatory
Information

Summary of Contents for P2422HE

















































































Search results

Summary of Contents for P2422HE

Reviews:

Brands by name

Popular brands

Dell P2422HE, User Manual

Search results

Summary of Contents for P2422HE

Reviews:

Brands by name

Popular brands