manualshive.com logo in svg

Dell OptiPlex 3020-Mini Tower, Owner'S Manual

Share
Download
Dell OptiPlex 3020-Mini Tower Owner'S Manual Download Page 35

Option

Description

– UEFI

Advanced Boot Options

Allows you to Enable Legacy Option 
ROMs

•

Enabled

 (Default)

Date/Time

Allows you to set the date and time. The 
changes to the system date and time 
takes effect immediately.

Table 3. System Configuration

Option

Description

Integrated NIC

Allows you to configure the integrated network controller. The 
options are:

• Disabled
• Enable UEFI Network Stack
• Enabled
•

Enabled w/PXE

 (Default)

• Enabled w/Cloud Desktop

Serial Port

Identifies and defines the serial port settings. You can set the 

serial port to:

•

Disabled

(Default)

• COM1
• COM2
• COM3
• COM4

NOTE: The operating system may allocate resources even if 
the setting is disabled.

SATA Operation

Allows you to configure the internal SATA hard-drive 

controller. The options are:

• Disabled
• ATA
•

AHCI

 (Default)

Drives

Allows you to enable or disable the various drives on-board:

• SATA-0
• SATA-1
• SATA-2

Default Setting: 

All drives are enabled.

SMART Reporting

This field controls if the hard drive errors for the integrated 

drives are reported during system startup. This technology is 

35

Summary of Contents for OptiPlex 3020-Mini Tower




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands