Dell OptiPlex 3010 Mini-Tower Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 59

background image

4.

Slide the intrusion switch toward the chassis bottom and remove it from the system board.

Related Links

Installing the Intrusion Switch

Installing the Intrusion Switch

1.

Insert the intrusion switch into the chassis rear and slide it toward the chassis top to secure it.

2.

Connect the intrusion switch-cable to the system board.

3.

Install the

cover

.

4.

Follow the procedures in

After Working Inside Your Computer

.

Related Links

Removing the Intrusion Switch

Removing The Speaker

1.

Follow the procedures in

Before Working Inside Your Computer

.

2.

Remove the

cover

.

3.

Disconnect the speaker cable from the system board.

16

«
...
14
15
16
17
18
...
»

Summary of Contents for OptiPlex 3010 Mini-Tower




























































Reviews:

No comments

Related manuals for OptiPlex 3010 Mini-Tower

Brand: Oldfields Pages: 2

Brand: Acer Pages: 51

ThinkCentre 8104

Brand: IBM Pages: 38

ECLIPSE MV/7800

Brand: Data General Service Pages: 167

Brand: Kontron Pages: 72

Literail Workstation 4 Person

Brand: Jason.L Pages: 4

Brand: Advantech Pages: 84

Brand: Matrox Pages: 174

Brand: Zotac Pages: 20

Brand: Asus Pages: 50

Brand: Asus Pages: 26

Brand: Asus Pages: 22

Brand: Asus Pages: 26

Brand: Asus Pages: 16

Brand: Asus Pages: 2

Brand: Asus Pages: 98

Brand: Asus Pages: 70

Brand: Asus Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands