Dell Inspiron 7420 Service Manual Download Page 52

Page: 52 / 85

I/O board

Removing the I/O board

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Enter the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

solid-state drive

7. Remove the

WWAN card

8. Remove the

battery

9. Remove the

heatsink assembly

10. Remove the

system board

About this task

The following images indicate the location of the I/O board and provide a visual representation of the removal procedure.

Steps

1. Remove the two (M2x4) screws that secure the I/O board to the computer.
2. Lift and remove the I/O board from the computer.

Installing the I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components

Summary of Contents for Inspiron 7420






















































































Search results

Summary of Contents for Inspiron 7420

Reviews:

Related manuals for Inspiron 7420

Brands by name

Popular brands

Dell Inspiron 7420, Service Manual

Search results

Summary of Contents for Inspiron 7420

Reviews:

Related manuals for Inspiron 7420

Brands by name

Popular brands