Dell Inspiron 3490 Service Manual Download Page 41 | Manualshive

Page: 41 / 86

background image

5. Lift the I/O board, along with the cable, off the palm-rest and keyboard assembly.

Replacing the I/O board

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

1. Using the alignment posts, place the I/O board on the palm-rest and keyboard assembly.
2. Replace the two screws (M2x4) that secure the I/O board to the palm rest and keyboard assembly.
3. Adhere the I/O-board cable to the palm rest and keyboard assembly.
4. Connect the hard-drive cable to the system board and close the latch to secure the cable.
5. Connect the I/O-board cable to the system board and close the latch to secure the cable.

Removing and installing components

41

«
...
39
40
41
42
43
...
»

Summary of Contents for Inspiron 3490























































































Reviews:

No comments

Related manuals for Inspiron 3490

SIERRA WIRELESS 250U 4G/3G LAPTOP CARD

Brand: Time Warner Cable Pages: 5

Presario,Presario 2701

Brand: Compaq Pages: 136

Brand: Acer Pages: 234

Brand: bto Pages: 308

1526 - Inspiron - Laptop

Brand: Dell Pages: 51

1720 - Vostro - Core 2 Duo 2.2 GHz

Brand: Dell Pages: 66

1737 - Studio - Laptop

Brand: Dell Pages: 47

T4310 - LifeBook Tablet PC

Brand: Fujitsu Pages: 401

Brand: Sharp Pages: 83

Satellite Pro S300M-W3401V

Brand: Toshiba Pages: 5

Satellite Pro S300M-S2142

Brand: Toshiba Pages: 5

Satellite Pro S300M-EZ2421

Brand: Toshiba Pages: 5

Satellite Pro S300-S2503

Brand: Toshiba Pages: 5

Satellite Pro S300-S2504

Brand: Toshiba Pages: 5

Satellite Pro S300-S1001

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ2521

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ2502

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ1514

Brand: Toshiba Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands