Dell Inspiron 14 5401 Service Manual Download Page 14

Page: 14 / 82

3. Using a plastic scribe, pry the base cover beside the display hinges, and then continue to work on the sides to open the base cover.
4. Disconnect the battery cable from the system board.

NOTE:

Disconnect the battery cable only when you are continuing to remove other components from your computer.

5. Press and hold the power button for five seconds to ground the computer and drain the flea power.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for Inspiron 14 5401



















































































Search results

Summary of Contents for Inspiron 14 5401

Reviews:

Related manuals for Inspiron 14 5401

Brands by name

Popular brands

Dell Inspiron 14 5401, Service Manual

Search results

Summary of Contents for Inspiron 14 5401

Reviews:

Related manuals for Inspiron 14 5401

Brands by name

Popular brands