Dell G3 15 3500 Service Manual Download

Page: 41 / 75

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

2. Remove the

About this task

The following image indicates the location of the heat sink and provides a visual representation of the removal procedure.

Steps

1. In the sequential order (1>2>3>4>5>6>7>8), loosen the eight captive screws that secure the heat sink to the system board.
2. Lift the heat sink off the system board.

Installing the heat sink

Prerequisites

If your are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the heat sink and provides a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for G3 15 3500












































































Search results

Summary of Contents for G3 15 3500

Reviews:

Related manuals for G3 15 3500

Brands by name

Popular brands

Dell G3 15 3500, Service Manual

Search results

Summary of Contents for G3 15 3500

Reviews:

Related manuals for G3 15 3500

Brands by name

Popular brands