Dell G16 7620 Service Manual Download Page 43

Page: 43 / 79

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

6. Install the

7. Follow the procedure in

After working inside your computer

Removing the system board (NVIDIA GeForce RTX 3050 Ti
graphics card)

Prerequisites

1. Follow the procedure in

Before working inside your computer

CAUTION:

Before removing the system board, give sufficient time for the heat sink to cool down to avoid

injury.

NOTE:

Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup

program. Make the appropriate changes again after you replace the system board.

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

NOTE:

This procedure only applies to computers shipped with a NVIDIA GeForce 3050 Ti graphics card.

About this task

The following image indicates the connectors on your system-board assembly.

1. Display cable
2. DDS (Dynamic Display Switch) cable
3. Speaker cable
4. Right-fan cable
5. Power-adapter port cable

Removing and installing components

Summary of Contents for G16 7620
















































































Search results

Summary of Contents for G16 7620

Reviews:

Dell G16 7620, Service Manual, Page: 43 / 79

Search results

Summary of Contents for G16 7620

Reviews: