Dell E70S Installation And Service Manual Download Page 12 | Manualshive

Page: 12 / 238

background image

Table 3. Left control panel with optional iDRAC Quick Sync 2 indicator (continued)

Item

Indicator, button, or

connector

Icon

Description

2

System health and system
ID indicator

Indicates the system health. For more information, see the

System health and system ID indicator codes

section.

3

iDRAC Quick Sync
2 wireless indicator
(optional)

Indicates if the iDRAC Quick Sync 2 wireless option is
activated. The Quick Sync 2 feature allows management of the
system using mobile devices. This feature aggregates hardware/
firmware inventory and various system level diagnostic/error
information that can be used in troubleshooting the system. You
can access system inventory, Dell Lifecycle Controller logs or
system logs, system health status, and also configure iDRAC,
BIOS, and networking parameters. You can also launch the virtual
Keyboard, Video, and Mouse (KVM) viewer and virtual Kernel-
based Virtual Machine (KVM), on a supported mobile device.
For more information, see the Integrated Dell Remote Access
Controller User's Guide at

www.dell.com/poweredgemanuals

.

NOTE:

For more information about the indicator codes, see the

System diagnostics and indicator codes

section.

Right control panel view

Figure 7. Right control panel view

Table 4. Right control panel

Ite

m

Indicator or button

Icon

Description

1

Power button

Indicates if the system is powered on or off. Press the power button to
manually power on or off the system.

NOTE:

Press the power button to gracefully shut down the ACPI-

compliant operating system.

2

USB 2.0-compliant port

The USB port is a 4-pin connector and 2.0-compliant. This port enables
you to connect USB devices to the system.

3

iDRAC Direct port
(Micro-AB USB)

The iDRAC Direct port (Micro-AB USB) enables you to access the iDRAC
Direct Micro-AB features. For more information, see the

iDRAC User's

Guide

available at

https://www.dell.com/idracmanuals

.

NOTE:

You can configure iDRAC Direct by using a USB to micro USB

(type AB) cable, which you can connect to your laptop or tablet. Cable
length should not exceed 3 feet (0.91 meters). Performance could be
affected by cable quality.

4

VGA port

Enables you to connect a display device to the system.

12

System overview

«
...
10
11
12
13
14
...
»

Summary of Contents for E70S















































































































































































































































Reviews:

No comments

Related manuals for E70S

Brand: D-Link Pages: 12

Brand: IBM Pages: 84

Brand: IBM Pages: 110

Brand: Korenix Pages: 2

FusionServer G5500 V6

Brand: xFusion Digital Technologies Pages: 100

Crestron 908012

Brand: SIERRA VIDEO SYSTEMS Pages: 32

SuperServer 5013G-M

Brand: Supero Pages: 104

Eternus DX80 S2

Brand: Fujitsu Pages: 186

Brand: Fujitsu Pages: 242

Brand: Honeywell Pages: 8

Brand: Honeywell Pages: 16

Brand: Honeywell Pages: 56

Uniformance R300

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 66

Brand: Honeywell Pages: 88

Brand: Honeywell Pages: 97

Brand: Honeywell Pages: 108

Brand: QNAP Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands