Dell Alienware 18 Owner'S Manual Download Page 91

Page: 91 / 119

Removing

the

Video

Card(s) |

Removing the Video Card(s)

WARNING:

Before working inside your computer, read the safety

information that shipped with your computer and follow the steps in
"Before You Begin" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove any installed card or blank from the Media-Card Reader.

Remove the base cover. See "Removing the Base Cover" on page 14.

Remove the fans cover. See "Removing the Fans Cover" on page 29.

Remove the battery pack. See "Removing the Battery Pack" on page 16.

Remove the hard drive(s). See “Removing the Hard Drive(s)” on page 25.

Remove the optical drive. See "Removing the Optical Drive" on page 22.

Remove the display assembly. See "Removing the Display Assembly" on page 56.

Procedure

Disconnect the video-card connector cable from the connectors on the system
board.

Lift the video-card connector cable off the computer base.

video-card connector cable

Book.book Page 91 Friday, June 28, 2013 11:10 AM

Summary of Contents for Alienware 18
























































































































Search results

Summary of Contents for Alienware 18

Reviews:

Related manuals for Alienware 18

Brands by name

Popular brands

Dell Alienware 18, Owner'S Manual

Search results

Summary of Contents for Alienware 18

Reviews:

Related manuals for Alienware 18

Brands by name

Popular brands