Dell Alienware 18 Owner'S Manual Download Page 25

Page: 25 / 119

Removing the Hard Drive(s) |

Removing the Hard Drive(s)

WARNING:

Before working inside your computer, read the safety

information that shipped with your computer and follow the steps in
"Before You Begin" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

CAUTION:

To avoid data loss, do not remove the hard drive while the

computer is in Sleep or On state.

CAUTION:

Hard drives are extremely fragile. Exercise care when

handling the hard drive.

Prerequisites

Remove the base cover. See "Removing the Base Cover" on page 14.

Remove the battery pack. See "Removing the Battery Pack" on page 16.

Book.book Page 25 Friday, June 28, 2013 11:10 AM

Summary of Contents for Alienware 18
























































































































Search results

Summary of Contents for Alienware 18

Reviews:

Related manuals for Alienware 18

Brands by name

Popular brands

Dell Alienware 18, Owner'S Manual

Search results

Summary of Contents for Alienware 18

Reviews:

Related manuals for Alienware 18

Brands by name

Popular brands