Dell Alienware 13 R3 Page 68 Service Manual Download

Page: 68 / 78

Removing the display back-cover and antenna

assembly

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps
in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

NOTE: These instructions are applicable only for laptops with a non-touch screen display.

1. Remove the

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Remove the

9. Remove the

10. Remove the

11. Remove the

12. Remove the

13. Remove the

14. Remove the

15. Remove the

16. Remove the

Procedure

After performing the steps in prerequisites we are left with the display back-cover and antenna assembly .

Summary of Contents for Alienware 13 R3















































































Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands

Dell Alienware 13 R3, Service Manual

Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands