Dell EMC VxRail E series Deployment Manual Download Page 31 | Manualshive

Page: 31 / 54

background image

31

Dell EMC VxRail Multirack Deployment Guide

sfo01-leaf03#

show ip route ospf

Codes: C - connected
S - static
B - BGP, IN - internal BGP, EX - external BGP
O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1,
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1,
E2 - OSPF external type 2, * - candidate default,
+ - summary route, > - non-active route
Gateway of last resort is not set
  Destination Gateway Dist/Metric Last Change
--------------------------------------------------------------------------------
-
  O 10.222.222.1/32 via 192.168.1.10 eth1/1/53 110/4 21:52:55
     via 192.168.2.10 eth1/1/54
  O 10.222.222.4/32 via 192.168.1.10 eth1/1/53 110/3 21:52:55
via 192.168.2.10 eth1/1/54
  O 10.222.222.64/32 via 192.168.1.10 eth1/1/53 110/4 21:52:55
     via 192.168.2.10 eth1/1/54
  O 192.168.1.0/31 via 192.168.1.10 eth1/1/53 110/3 21:53:01
  O 192.168.1.2/31 via 192.168.1.10 eth1/1/53 110/3 21:53:01
  O 192.168.1.12/31 via 192.168.1.10 eth1/1/53 110/2 21:53:01
  O 192.168.1.14/31 via 192.168.1.10 eth1/1/53 110/2 21:53:01
  O 192.168.1.252/31 via 192.168.1.10 eth1/1/53 110/3 21:53:01
  O 192.168.2.0/31 via 192.168.2.10 eth1/1/54 110/3 21:52:55
  O 192.168.2.2/31 via 192.168.2.10 eth1/1/54 110/3 21:52:55
  O 192.168.2.12/31 via 192.168.2.10 eth1/1/54 110/2 21:52:55
  O 192.168.2.14/31 via 192.168.2.10 eth1/1/54 110/2 21:52:55
  O 192.168.2.252/31 via 192.168.2.10 eth1/1/54 110/3     21:52:55

6.2.3

show ip ospf topology

The

show ip ospf topology

command verifies the structure of the network.

sfo01-leaf03#

show ip ospf topology

Router ID Flags Cost Nexthop Interface Area
-----------------------------------------------------------
10.0.1.1   -/-/-/ 1 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.1.2   -/-/-/ 1 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.1   -/-/-/ 3 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.1   -/-/-/ 3 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.2   -/-/-/ 3 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.2   -/-/-/ 3 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.6   -/-/-/ 2 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.6   -/-/-/ 2 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.7   -/-/-/ 2 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.7   -/-/-/ 2 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.8   -/-/-/ 2 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.8   -/-/-/ 2 192.168.2.10 ethernet1/1/54 0.0.0.0
10.0.2.64 -/-/-/ 3 192.168.1.10 ethernet1/1/53 0.0.0.0
10.0.2.64 -/-/-/ 3 192.168.2.10 ethernet1/1/54 0.0.0.0

«
...
29
30
31
32
33
...
»

Summary of Contents for VxRail E series























































Reviews:

No comments

Related manuals for VxRail E series

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: H3C Pages: 6

OfficeConnect 3CP4144

Brand: 3Com Pages: 4

OfficeConnect 3CP4144

Brand: 3Com Pages: 2

Brand: H3C Pages: 60

Brand: H3C Pages: 149

Brand: 3Com Pages: 27

Brand: Watchguard Pages: 39

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

Brand: Macsense Pages: 39

AAA-130SA SERIES

Brand: Adaptec Pages: 94

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

HHM Series HHM2245SA1

Brand: TDK Pages: 2

Brand: Digi Pages: 116

Brand: Gemtek Systems Pages: 51

Brand: Kontron Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands