Dell EMC PowerProtect DD9900 Installation Manual Download Page 64

Page: 64 / 96

Connecting DS60 shelves

The cabling diagrams in this section show maximum configurations. Not all systems will have all the
disk shelves shown in the diagrams.

When connecting DS60 shelves, all the cables have HD-mini-SAS connectors at both ends.

Add shelf-to-shelf cables between shelves in a loop and to the controller as shown in the diagrams.

Connect an FS25 shelf with DS60 shelves

Connect the FS25 shelf to the controller as shown in the diagrams.

There are no specific placement or cabling requirements for SSD shelves.

The SSD shelf counts towards the total number of shelves connected to the system.

Note:

The following diagrams show maximum configurations. Not all systems will have

everything depicted.

DD9900 with DS60 cabling

The DD9900 system supports a maximum of five shelves. The diagram shows them cabled in two
sets of two shelves each, and one set of one shelf. The FS25 SSD shelf is cabled as a separate set
from the DS60 shelves.

Table 9 DD9900 with DS60 cabling instructions: Single node or HA primary node

String
(Loop)

I/O - Port

Shelf Port

Length

I/O 7 - Port A

LCC A, port 0 of shelf V1.1

I/O 3 - Port A

LCC B, port 0 of the highest number shelf in V1

I/O 7 - Port B

LCC A, port 0 of shelf V2.1

I/O 3 - Port B

LCC B, port 0 of the highest number shelf in V2

I/O 7 - Port C

LCC A, port 0 of shelf V3.1

I/O 3 - Port C

LCC B, port 0 of shelf V3.1

I/O 7 - Port D

FS25 LCC B, port A

I/O 3 - Port D

FS25 LCC A, port A

a. Cable lengths shown are designed for Dell EMC racks. Longer cables (up to 5M) can be

used.

Table 10 DD9900 with DS60 cabling instructions: HA standby node (HA only)

String
(Loop)

I/O - Port

Shelf Port

Length

I/O 7 - Port A

LCC A, port 2 of the highest number shelf in V1

I/O 3 - Port A

LCC B, port 2 of shelf V1.1

I/O 7 - Port B

LCC A, port 2 of the highest number shelf in V2

I/O 3 - Port B

LCC B, port 2 of shelf V2.1

Connect Cables and Power On

Dell EMC PowerProtect DD9900 System Installation Guide

Summary of Contents for PowerProtect DD9900

































































































Search results

Summary of Contents for PowerProtect DD9900

Reviews:

Related manuals for PowerProtect DD9900

Brands by name

Popular brands

Dell EMC PowerProtect DD9900, Installation Manual

Search results

Summary of Contents for PowerProtect DD9900

Reviews:

Related manuals for PowerProtect DD9900

Brands by name

Popular brands