Dell EMC PowerProtect DD9900 Installation Manual Download Page 25

Page: 25 / 96

Figure 11 Attach inner CMA bracket to the rails

3. Repeat the preceding steps to attach the outer and inner brackets to the other rail.

Install the rails

About this task

The rails are labeled left and right, and cannot be interchanged. The front side of each rail is
labeled Left Front or Right Front.
Install the left rail first, and then repeat the procedure for the right rail.

Procedure

1. Hold the rail with the rail end pieces labeled FRONT facing the front of the rack flanges.

2. Align the back rail end piece until it is seated on the rack flange and the latch clicks into

place.

3. Align the front rail end piece until it is seated on the rack flange and the latch clicks into

place.

Install the System in the Rack

Dell EMC PowerProtect DD9900 System Installation Guide

Summary of Contents for PowerProtect DD9900

































































































Search results

Summary of Contents for PowerProtect DD9900

Reviews:

Related manuals for PowerProtect DD9900

Brands by name

Popular brands

Dell EMC PowerProtect DD9900, Installation Manual

Search results

Summary of Contents for PowerProtect DD9900

Reviews:

Related manuals for PowerProtect DD9900

Brands by name

Popular brands