Dell EMC ECS D Series Hardware Manual Download Page 30

Page: 30 / 114

2. RMM: A dedicated port for hardware monitoring (per node)

3. SAS to DAE. Used on U- and D-Series servers only. U-Series Gen1 has a single

port. U-Series Gen2 hardware has two ports. The D-Series has one high density
SAS cable with one connector.

4. 10 GbE SW2 (

hare): The left 10 GbE data port of each node is connected to one of

the data ports on the 10 GbE (SW2) switch

5. 10 GbE SW1 (

rabbit): The right 10 GbE data port of each node is connected to one

of the data ports on the 10 GbE (SW1) switch

Rack and node host names

Lists the default rack and node host names for an ECS appliance.

Default rack IDs and color names are assigned in installation order as shown below:

Table 17 Rack ID 1 to 50

Rack
ID

Rack color

Rack
ID

Rack color

Rack
ID

Rack color

red

carmine

cornsilk

green

auburn

ochre

blue

bronze

lavender

yellow

apricot

ginger

magenta

jasmine

ivory

cyan

army

carnelian

azure

copper

taupe

violet

amaranth

navy

rose

mint

indigo

orange

cobalt

veronica

chartreuse

fern

citron

pink

sienna

sand

brown

mantis

russet

white

denim

brick

gray

aquamarine

avocado

beige

baby

bubblegum

silver

eggplant

Nodes are assigned node names based on their order within the server chassis and
within the rack itself. The following table lists the default node names.

Table 18 Default node names

Node

Node name

Node

Node name

Node

Node name

provo

boston

memphis

Servers

D- and U-Series

Hardware Guide

Summary of Contents for ECS D Series



















































































































Search results

Summary of Contents for ECS D Series

Reviews:

Related manuals for ECS D Series

Brands by name

Popular brands

Dell EMC ECS D Series, Hardware Manual

Search results

Summary of Contents for ECS D Series

Reviews:

Related manuals for ECS D Series

Brands by name

Popular brands