Dell EMC ECS D Series Hardware Manual Download Page 64

Page: 64 / 114

connectors with corresponding LEDs. These LEDs indicate the link and activity of each
SAS connector for input and output to devices.

Note

Disconnect power to the DAE when changing the ICM.

Table 38 ICM bus status LEDs

LED

Color

State

Description

Power fault

Green

Power on

—

Off

Power off

Power on

Amber

Fault

—

Off

No fault or power off

The ICM supports the following I/O ports on the rear:

Four 6 Gb/s PCI Gen2 SAS ports

One management (RJ-12) connector to the SPS (field service diagnostics only)

One USB connector

One 6 Gb/s SAS x8 ports

It supports four 6 Gb/s SAS x8 ports on the rear of the ICM (two inputs and two
outputs, one used in Gen1 hardware and two used in Gen2 hardware). This port
provides an interface for SAS and NL-SAS drives in the DAE.

Table 39 ICM 6 Gb/s port LEDs

LED

Color

State

Description

Link/Activity

Blue

Indicates a 4x or 8x connection with all lanes
running at 6 Gb/s.

Green

Indicates that a wide port width other than 4x
or 8x has been established or one or more
lanes is not running at full speed or
disconnected.

—

Off

Not connected.

Disk Drives

D- and U-Series

Hardware Guide

Summary of Contents for ECS D Series



















































































































Search results

Summary of Contents for ECS D Series

Reviews:

Related manuals for ECS D Series

Brands by name

Popular brands

Dell EMC ECS D Series, Hardware Manual

Search results

Summary of Contents for ECS D Series

Reviews:

Related manuals for ECS D Series

Brands by name

Popular brands