Deliberant FWBD0501 Page 56 User Manual Download | Manualshive

Page: 56 / 67

background image

User’s

Guide

deliberant

Page

56

Firmware

Upgrade

To update your device firmware use the

System | Firmware upgrade

menu. Press

Upload firmware

,

select the firmware file and click the

Upload

firmware

button:

Current version

– displays version of the current firmware.

Upload firmware

– click the button to select the new firmware image for uploading it to the device.

The device system firmware upgrade is compatible with all configuration settings. When the device is
upgraded with a newer version or the same version builds, all the system’s configuration will be
preserved after the upgrade.

The new firmware image is uploaded to the controller’s temporary memory. It is necessary to save the
firmware into the device permanent memory. Click the Upgrade button:

Upgrade

– upgrade device with the uploaded image and reboot the system.

Do not switch off and do not disconnect the device from the power supply during the
firmware upgrade process as the device could be damaged.

«
...
54
55
56
57
58
...
»

Summary of Contents for FWBD0501




































































Reviews:

No comments

Related manuals for FWBD0501

Brand: AirM2M Pages: 64

Brand: Linkskey Pages: 8

Brand: Meru Networks Pages: 73

Brand: TP-Link Pages: 2

InstantWave NWH660

Brand: NDC Pages: 53

AisStation WHR-G54S

Brand: Buffalo Pages: 82

Aruba 318 Series

Brand: Hewlett Packard Enterprise Pages: 2

Brand: Huawei Pages: 117

Brand: Huawei Pages: 24

Brand: Huawei Pages: 122

Brand: Huawei Pages: 78

Brand: Huawei Pages: 25

Brand: Huawei Pages: 172

Brand: Huawei Pages: 37

Brand: Huawei Pages: 17

Brand: Huawei Pages: 33

AP6510DN-AGN-US

Brand: Huawei Pages: 14

Brand: Huawei Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands