Del ozone Big Dipper EC-AG1U Installation & Operation Manual Download Page 7

3

EC–AG 

Installation & Operations Manual

Generator to operate safely under vacuum. 

Note: The Injector 

needs to be installed after all other equipment or possible failure 
may occur.

2D-1. Plumbing the Above Ground Injector Assembly 
Note:
 Figure 2 and the instructions below describe Injector 
installation immediately after the Filter. For pools equipped with a 
heater, the Injector must be installed AFTER the heater. The fittings 
provided may be used to connect the Injector directly to the wall of 
the pool or the outlet of the heater.
a. Wrap Teflon tape on all male pipe threads. 
b. Disconnect the pool’s return hose from the Filter. Keep the hose 

elevated to aviod draining the pool. 

c.  Use either the straight or elbow fittings provided to connect the 

Injector to the discharge port of the Filter. Ensure that the flow 
arrow on the Injector is pointed in the direction of water flow, and 
that the Ozone Port is accessible.

d. Reconnect the pool’s return hose to the outlet of the injector.
e. Attach Hose Barb Fitting to the Ozone Port on the Injector.

2D-2. Ozone Gas Line
Connect the end of the Ozone Supply Tubing that is closest to the 
Check Valve to the Hose Barb Fitting on the Injector. Secure with a 
supplied hose clamp. If the Ozone Generator is mounted above the 
water line attach the other end of the Ozone Supply Tubing to the 
ozone out fitting on the EC–AG and secure with the supplied hose 
clamps. 

If the Ozone Generator is mounted below the water 

line, the Ozone Supply Tubing must be run to a point above the 
water line.
 Simply coil the tubing into a complete circle about 6˝ 
diameter and fasten it above the water line. This will act as a water 
trap to prevent water from running back to the Ozone Generator.

SECTION 3 Operation

3A. General 

To achieve optimal performance from the Ozone Generator, the pool 
must be as clean as possible to start with.
a. Backwash or clean filters one day before starting  the Ozone 

Generator. 

b. Superchlorinate pool water using a chlorine based shock 

treatment. 

Summary of Contents for Big Dipper EC-AG1U

















Reviews: