Del ozone Big Dipper EC-AG1U Installation & Operation Manual Download Page 4

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

•  Read this manual completely before attempting installation. 
•  All permanent electrical connections should be made by a qualified  

 

 electrician. 
•  Connect to a grounding type receptacle only. If the ozone generator    
  electrical connection is to be attached to the pool controls, be sure  

 

  the pool controls are protected by a Ground Fault Circuit Interrupter    
  (G.F.C.I.). If the ozone generator is connected to an independent  

 

  electrical supply, then a G.F.C.I. must be installed between the ozone    
  generator and the electrical supply. 
•  Do not bury cord. 
•  Warning – To reduce the risk of electrical shock, replace damaged cord  
 immediately. 
•  Install at least 5 feet (1.5 meters) from wall of pool. Install ozone  

 

  generator no less than one (1) foot above maximum water level to  

 

  prevent water from contacting electrical equipment. Install in    

 

  accordance with the installation instructions. 
•  Follow all applicable electrical codes. 
•  Electric shock hazard. Be sure to turn power OFF and disconnect from  
  power source before any service work is performed. Failure to do so    
  could result in serious injury or death. 
•  The ozone generator must be installed in an outdoor location,   

 

  or indoors in a forced air ventilated room, and installed so that the  

 

  orientation is exactly as shown in Figure 1. 
•  Mount the ozone generator so that it is inaccessible to anyone in the    
  pool. Never attempt any servicing while unit is wet. 
•  Plastic ozone supply tubing is supplied with the ozone generator.  

 

  Never replace this tubing with metal tubing. 
•  Warning – Short-term inhalation of high concentrations of ozone and    
  long term inhalation of low concentrations of ozone can cause serious   
  harmful physiological effects. DO NOT inhale ozone gas produced by    
  this device. 
•  For your safety, do not store or use gasoline, chemicals or other  

 

  flammable liquids or vapors near this or any other appliance.

SAVE THESE INSTRUCTIONS!

EC–AG1U, EC–AG2U

Summary of Contents for Big Dipper EC-AG1U

















Reviews: