Dekolink Deko2119 Product Manual Download Page 7

Page: 7 / 53

EKOLINK

IRELESS

. M

INI

-R

EPEATER

EKO

2119 P

RODUCT

ANUAL

Pub. 313-2006 Rev. 2.01S

Proprietary Data

Page i

CONTENTS

1. INTRODUCTION

..................................................................................... 1

1.1 General

........................................................................................................................ 1

1.2 Applications

................................................................................................................. 1

1.3 Main Features

.............................................................................................................. 2

1.4 Description

.................................................................................................................. 2

1.5 Controls and Indicators

............................................................................................... 3

1.6 Model and Frequencies

................................................................................................ 5

1.7 Unpacking and Inspection

............................................................................................ 6

2. FUNCTIONAL DESCRIPTION

................................................................ 7

2.1 General

........................................................................................................................ 7

3. SPECIFICATIONS

................................................................................... 9

3.1 General

........................................................................................................................ 9

3.2 Electrical Specifications

............................................................................................... 9

3.3 General Specifications

................................................................................................. 9

3.4 Mechanical Specifications

.......................................................................................... 10

3.5 Environmental Specifications

..................................................................................... 10

3.6 Connectors

................................................................................................................ 11

4. INSTALLATION AND OPERATION

..................................................... 12

4.1 General

...................................................................................................................... 12

4.2 Safety Instructions

..................................................................................................... 12

4.3 Installation Site Considerations

................................................................................. 12

4.4 Tools and Materials

................................................................................................... 12

4.5 Installation Procedures

.............................................................................................. 12

4.6 Antenna Installation Site – Considerations

................................................................. 14

4.7 Connection to Antennas and to Power

........................................................................ 14

4.8 Operating Procedures

................................................................................................ 15

4.9 Donor Antenna Alignment

......................................................................................... 16

4.10 RF Exposure Warning

............................................................................................. 17

5. DUAL-BAND MINI-REPEATERS CONFIGURATION

.......................... 18

6. DAISY-CHAINED DUAL-BAND MINI-REPEATERS

............................ 19

7. SETUP (monitoring and control)

............................................................. 20

7.1 General

...................................................................................................................... 20

7.2 Local Mode Connection

............................................................................................. 20

7.3 Repeater Management System (RMS)

........................................................................ 21

7.4 RMS650 – Main Screen Description

........................................................................... 23

7.5 Selecting Deko2119

.................................................................................................... 24

7.6 RMS 650 Screens Operation

...................................................................................... 27

7.7 Selecting the Operating Sub-Bands

............................................................................ 30

7.8 Finalizing the Operation Procedures

.......................................................................... 34

7.9 Alarms Screen

........................................................................................................... 35

7.10 Configuration Screen

............................................................................................... 36

7.11 Exiting the RMS Software

........................................................................................ 37

Summary of Contents for Deko2119





















































Search results

Summary of Contents for Deko2119

Reviews:

Brands by name

Popular brands

Dekolink Deko2119, Product Manual

Search results

Summary of Contents for Deko2119

Reviews:

Brands by name

Popular brands