manualshive.com logo in svg

Dekolink Deko2119, Product Manual

Share
Download
Dekolink Deko2119 Product Manual Download Page 20

P

RODUCT 

M

ANUAL

 

M

INI

-R

EPEATER 

D

EKO

2119 D

EKOLINK 

W

IRELESS 

L

TD

. 

Page 12 

Proprietary Data 

Pub. 313-2006 Rev. 2.01S 

4.

 

INSTALLATION AND OPERATION  

4.1 G

ENERAL 

 

The small, lightweight Mini-Repeater Deko2119 is easy-to-install.  Measurement 
tools are most always never needed.  

4.2 S

AFETY 

I

NSTRUCTIONS 

 

Before installing the Repeater, review the following safety information:  

•

 

Follow all local safety regulations when installing the Repeater  

•

 

Only qualified personnel are authorized to install and maintain the 
Repeater  

•

 

Follow Electro-Static Discharge (ESD) precautions.  

4.3 I

NSTALLATION 

S

ITE 

C

ONSIDERATIONS 

 

The 

Mini-Repeater Deko2119 is provided with back panel flanges for easy 

installation on any surface (see Figure 5).  It is recommended to install the 
Mini-Repeater on a flat rigid surface. The installation site for the Mini-Repeater

 

should take into consideration the following conditions: 

•

 

The Repeater should be installed in a ventilated and easy-to-reach area  

•

 

The Repeater is convection cooled so the area should be unblocked to 
ensure airflow.  

4.4 T

OOLS AND 

M

ATERIALS 

 

Measurement tools are most always never needed.  No special tools are 
necessary. However, a standard, professional, tool box is required for the 
installation procedures.   

4.5 I

NSTALLATION 

P

ROCEDURES

 

The wall mount installation is the preferred method of installation for the 
Repeater.  Determine the location of the Repeater on the wall. The location 
should be at normal eye level height, above ground.  

Proceed as follows: 

•

 

Mark the three drilling holes on the surface of the wall based on the 
mounting holes on the Repeater chassis – see Figure 5  

•

 

Drill the appropriate three (3) holes in the wall. Recommend the screw 
sizes to use, such as: “It is recommended to use No. 8 screws”. 

•

 

Align the housing so that the mounting brackets fit into the holes in 
the wall  

•

 

Use hex-head screws or bolts, and washers to secure the enclosure 
firmly to the wall. Recommend the screw sizes to use, such as: “It is 
recommended to use No. 8 screws. The mounting screws should not 
be smaller than no. 6.” 

Note 

Bolts and washers are not supplied with the Repeater  

Summary of Contents for Deko2119






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands