manualshive.com logo in svg

Dekolink Deko2119, Product Manual

Share
Download
Dekolink Deko2119 Product Manual Download Page 28

P

RODUCT 

M

ANUAL

 

M

INI

-R

EPEATER 

D

EKO

2119 D

EKOLINK 

W

IRELESS 

L

TD

. 

Page 20 

Proprietary Data 

Pub. 313-2006 Rev. 2.01S 

7.

 

SETUP (MONITORING AND CONTROL) 

7.1 G

ENERAL

 

This section provides the setup procedures for Mini-Repeater Deko2119.   

The Mini-Repeater is set for plug and play operation, and usually this is 
sufficient.  However, you are probably required to set the channels (filters) 
bandwidths.  This requires setup procedures described in this section.  These 
procedures also provide the steps to obtain more information about the repeater 
such as monitoring and parameters setting, as well as alarms.   

The setup is performed in a local (defined as automatic in the software) mode 
with the help of the RMS software installed on a host computer (usually, a 
laptop).   

7.2 L

OCAL 

M

ODE 

C

ONNECTION

 

To set up a local connection (see Figure 9): 

•

 

Turn on the Repeater and wait for the three LEDs on the front panel to 
turn on and show steady green  

•

 

Connect an external serial cable from a PC (COM interface) to the 
communications port in the bottom panel.  

Note  

The RS-232 cable connector should be DB-9 pin type, pins 2,3 crossed, and 

female-to-female terminated [supplied with the repeater].  

 

 

Figure 9: Mini-Repeater - Local Monitoring with Laptop  

 

Summary of Contents for Deko2119






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands