DEGXEL 1000W Operating Instructions Manual Download Page 3

Page 3

www.degxel.com

En

gli

sh

2 | 

TECHNICAL SPECIFICATIONS

The Degxel™ heaters are infrared heaters in accordance to the CE & ROHS (230V/50Hz) standards. They are 

certified by the German inspection body TUV/GS. They are divided into several ranges:

The infrared radiation (IR) is an electromagnetic radiation of a greater length than that the one of a visible light 

wave (so it is invisible). It is comparable to a sunlight that we cannot see but we feel the heat when we are 

exposed to it. A high temperature heat source emits infrared which are afterwards absorbed by a cold body that 

restore them again. The heat can therefore be transmitted without contact by infrared radiation.

Thermal radiation is transmitted through the surface of the heater. This surface consists of an optimal heating 

body for the radiation. This radiation is transmitted to the “objects” that the infrared waves encounter on their path 

(floor, walls, ceiling, objects, people, etc.). The waves travel at 180° and are safe for humans. For more information 

about IR: www.foxof.com

Your Degxel™ heater:

   Heating elements: mesh composed of an alloy of copper and nickel.

   Front: metal sheet covered with a specific emissive powder. Adding an ESG Securit glass depending on the 

model.

   Technology: heating by far infrared radiation.

   Radiator surface temperature: [90°C-110°C] according to AC voltage [220-240V].

   IP code: IP45.

   IEC Protection class: Class 1.

   Power (watt): from 210W to 1020W according to models.

   Connection to standard socket with ground: AC [230V] 50/60 Hz (from 16 A). Electric power line taken directly 

from the switchboard.

   Integrated temperature sensors: for automatic stop if necessary.

   Mounting: 2 mounting pads on the back and 2 steel plates to be fixed to the wall. 4 peripheral rollers for adjust

-

ment-locking. Wall or ceiling mounting. See the installation section.

   Power cable: Type CEE 7/7 tilted, 8 mm flat, length : 1.9 m

   Warranty: see warranty section.

   Very low electromagnetic pollution.

   CE standard, certified TUV GS, TUV EMC, ROHS.

   Declaration of conformity: EN60335-1, EN60335-2-30, EN50366.

   Certified manufacturing origin: Austria. Heat4all Gmbh.

    Mirror heaters
    Glass heaters
    Picture heaters  

    Extra flat heaters

    Towel heaters 
    Outdoor heaters

Summary of Contents for 1000W













Reviews: