background image

 

Product description 

 

 

 

Bushings

 

 

Hexagon screws 3 mm   

 

Status LED 
„ALARM“ 

 

Status LED „POWER“ 

 

Status LED „ERROR“

 

 

Sensor module 

 

Mounting holes

 

 

PCB electronics 

 

 

 

Jumper connector of 
the terminating 
resistor RS485

 

 

Terminal block RS485 B 

Terminal block RS485 

4-20 mA signal terminal 
block 

 

GND power supply 
terminal block

 

 

DIP switch for the 
RS485 adress

 

+24V DC Power 
supply terminal block

 

 

 

Assembly and disassembly of the transmitter 

Before assembling, read the valid instalation standarts EN 60079-29-2 (Selection, instalation, use and maintenance of 
detectors for combustible gases and oxygen) and EN 45544-4 (Guildelines for the selection, installation, use and maintenance 
of detectors of toxic substances).  
Secure that the sensor is reachable by air. The transmitter must be in a free area with no obstacles in its way (furniture etc.) 
Ensure that the input of the sensor cannot be polluted by layers of dust or other contamination.

  

To maintain IP protection the transmitter must be assambled with the sensor module facing downwards.

 

1.

 

Assembly of the transmitter

 

The transmitter consists of four parts - the body of the transmitter, the removable sensor and bushings.  
 
Transmitter assembly procedure is as follows: 

a)

 

Disassemble the transmitter with the four hexagon socket screws 3 mm 

b)

 

Use a screwdriver to break out holes for the bushings 

c)

 

Mount the transmitter on a flat surface with four 6 mm fasteners in height above the floor with the gas entrance 
facing downwards, as specified by the detected substance 

d)

 

Direct the cable trough the bushings 

e)

 

Connect the wiring to the terminal block according to " Installation of wiring for RS485".

 

f)

 

Assemble the transmitter with the four hexagon sockets scews 3 mm 

HRW Limited

[email protected]

www.hrw.hk

Summary of Contents for NB III LCD














Reviews: