background image

 10

Care and Cleaning

 

To prolong the original appearance, clean with clear water and a soft, damp cloth only.

 

Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature 
deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty.

 

Do not spray with a hose or power washer.

Troubleshooting

Problem

Possible Cause

Solution

The light will not come on.

 

The light switch is turned off.

 

Turn the light switch on.

 

The bulb is loose or burned out.

 

Check the bulb and replace 
if burned out.

 

The fuse is blown or the circuit breaker 
is turned off.

 

Replace the fuse or turn the 
circuit breaker on.

 

Daylight turn-off (photocell) is in effect.

 

Recheck after dark.

 

The circuit wiring is incorrect, if this is 
a new installation.

 

Verify the wiring is correct.

 

The motion sensor is aimed in the 
wrong direction.

 

Re-aim the motion sensor 
to cover the desired area.

 

The outside air temperature is close to 
the same as a person’s body heat.

 

Increase the “RANGE” 
setting.

The light comes on during the 
day.

 

The motion sensor may be installed in a 
relatively dark location.

 

The light fixture is operat-
ing normally under these 
circumstances.

 

The “ON-TIME” switch is in the “TEST” 
position.

 

Set the “ON-TIME” switch 
to the 1, 5, or 20 minute 
setting.

The light comes on for no 
apparent reason.

 

The motion sensor may be sensing 
small animals or automobile traffic.

 

Re-aim the motion sensor.

 

The “RANGE” dial is set too high.

 

Decrease the “RANGE” 
setting.

 

The “DUALBRITE” switch is in the 3 
hour, 6 hour, or dusk-to-dawn setting.

 

The light fixture is operat-
ing normally under these 
circumstances.

 

The outside temperature is much 
warmer or cooler than a person’s body 
heat (summer or winter).

 

Decrease the “RANGE” 
setting.

 

The light fixture is wired through a 
dimmer or timer.

 

Do not use a dimmer or 
timer to control the light 
fixture. Replace the dimmer 
or timer with a standard on/
off wall switch.

The lights turn off too late in 
Dusk-to-Dawn setting.

The light fixture may be installed in a 
relatively dark location.

Relocate the light fixture or use 
the 3 hour or 6 hour setting.

Summary of Contents for 703390

























Reviews: