DeDietrich Diematic iSystem Installation, User And Service Manual Download Page 78

Page: 78 / 88

Code Faults

Cause
of the
fault

Description

Checking / solution

L38

PCU COM.FAIL

PCU

Communication failure between

the PCU and SCU PCBs

Bad connection

Check the wiring between the PCU and SCU

PCBs

Run an

AUTODETECTION

in the menu

#CONFIGURATION

SCU PCB not connected or faulty

Replace the SCU PCB

L39

BL OPEN FAIL

PCU

The

inlet opened for a short

time

Bad connection

Check the wiring

External cause

Check the device connected to the

contact

Parameter incorrectly set

Check the parameter

IN.BL

D03
D04

OUTL S.B FAIL.
OUTL S.C FAIL.

SCU

Circuit B flow sensor fault

Circuit C flow sensor fault
Remarks:

The circuit pump is running.

The 3-way valve motor on the

circuit is no longer powered and

can be adjusted manually.

Bad connection

Check whether the sensor is connected:

See chapter: "Deletion of sensors from

the memory in the PCB", page 79

Check the link and the connectors

Check that the sensor has been correctly fitted

Sensor fault

Check the Ohmic value of the sensor

Replace the sensor if necessary

D05

OUTSI.S.FAIL.

SCU

Outside temperature sensor fault
Remarks:

The boiler operates on

BOILER

MAX

temperature.

The valve setting is no longer

ensured but monitoring the

maximum temperature of the

circuit after the valve is ensured.

Valves may be manually operated.

Reheating the domestic hot water

remains ensured.

Bad connection

Check whether the sensor is connected:

See chapter: "Deletion of sensors from

the memory in the PCB", page 79

Check the link and the connectors

Check that the sensor has been correctly fitted

Sensor fault

Check the Ohmic value of the sensor

Replace the sensor if necessary

D07

AUX.SENS.FAIL

SCU

Auxiliary sensor fault

Bad connection

Check whether the sensor is connected:

See chapter: "Deletion of sensors from

the memory in the PCB", page 79

Check the link and the connectors

Check that the sensor has been correctly fitted

Sensor fault

Check the Ohmic value of the sensor

Replace the sensor if necessary

7. Troubleshooting

Diematic iSystem For C 330 / C 630 ECO

31082018 - 7600691-001-06

Summary of Contents for Diematic iSystem

























































































Search results

Summary of Contents for Diematic iSystem

Reviews:

Related manuals for Diematic iSystem

Brands by name

Popular brands

DeDietrich Diematic iSystem, Installation, User And Service Manual

Search results

Summary of Contents for Diematic iSystem

Reviews:

Related manuals for Diematic iSystem

Brands by name

Popular brands