Connecting Wall Panel
!
WARNING
To prevent SERIOUS INJURY or DEATH from electrocution:
- Power MUST NOT be connected until instructed.
To prevent SERIOUS INJURY or DEATH from using the Wall Panel or Push Button and a closing door:
- Install the Wall Panel or Push Button within sight of the door at a minimum height of 5 feet (1.5m)
above the floor. Make sure it is out of the reach of children and moving parts of door and hardware.
- NEVER permit children to access the Wall Panel, Push Button or remote Transmitters.
- Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight.
- ALWAYS keep a moving door in sight until it’s completely closed.
- NEVER cross the path of a moving door.
Drywall Anchor
Screw #6 x1”
14
The Wall Panel is a wired, illuminated door control placed inside
your garage.
To install the Wall Panel:
1.
Inside your garage, install the rear cover of the Wall Panel
within sight of the door at a minimum height of 5 feet
(1.5m) off the ground. Ensure it is installed out of the reach
of children and free from the moving parts of the door and
hardware.
2.
With the “Arrow” icon on the rear cover pointing to up, se-
curely fasten it to a solid surface with 1” screws. If attach-
ing to drywall or other hollow surface, drill 3/16” holes and
use the provided Drywall Anchors.
3.
Snap the Wall Panel onto the rear cover
.
To Connect the Wall Panel to the Opener
Connect the pair of wires from the Wall Panel to the “Wall Box”
terminals on the rear of the Opener.
Using the Wall Panel
(ONLY after installation is completed and power is connect-
ed as instructed.)
Door
—Momentary press to access the door
Light
– Turns the courtesy light On/Off
Vacation Lock
OFF
— Door can be accessed by either access controls
ON
— Prevent access of door by Remote Transmitters
and Door button
From Wall Panel
Wall
Box
Wall Panel
Min. 5 feet (1.5m) above floor
Arrow icon points UP
Connecting Power
To Align the Photo Eye Safety System:
1.
When the Photo Eye System is properly connected and the
power is connected, one of the Photo Eyes will emit a
steady green light. This Photo Eye is the Emitter that
generates the Invisible Light Beam.
2.
When properly aligned, the Sensor should emit a steady
red light when it senses the invisible light beam from the
Emitter.
3.
If the indication is unsteady, flashes or is dim, check for
any obstructions and adjust the position until the Sensor
gives a STEADY RED LIGHT.
Note: The path of the invisible light beam MUST NOT be
obstructed. No part of the garage door or any
hardware should interfere with the beam or the Open-
er will not close the door.
!
Aligning the Photo Eye Safety System
For Permanent Wiring ONLY
DO NOT OPERATE OPENER AT THIS TIME.
To Connect Power
Plug the Opener into a grounded outlet ONLY. If there is no
grounded outlet present, call a qualified electrician to replace the
outlet.
Permanent Wiring (If Required by Local Code)
1.
Remove the enclosure by removing the 6 screws located
on the sides and rear of the Opener.
2.
Cut the two wire connectors found inside and remove the
power cord.
3.
Group neutral (white) wires from power source with 2 white
(W) wires and 1 yellow (Y) wire inside the Opener.
Connect them with a wire nut (not provided).
4.
Group line (black) wires from power source with black wire
(B) inside the Opener. Connect them with a wire nut
(not provided).
5.
Secure the ground (green or bare) wire from the power
source with a grounding screw.
6.
Reinstall the enclosure.
7.
Turn on power supply. If the wiring is properly connected,
a “click” should be heard and the light will illuminate (if a
bulb is installed). If there is no response from the Opener,
check power source and wiring.
!
WARNING
To prevent SERIOUS INJURY or DEATH from electrocution or fire:
- Power MUST be DISCONNECTED BEFORE proceeding with permanent wiring procedures.
- Garage Door Opener installation and wiring MUST be in compliance with all local electrical and building
codes. Make sure the Opener is ALWAYS grounded.
- NEVER use an extension cord, 2-wire adapter or modify the power plug in any way to make it fit the outlet.
Ground screw (green)
Conduit with wire
Y
W
Neutral (W)
B
Wire nut
W
Line (B )
Ground (G)
Ordinary Power Connection
Invisible Light Beam
15
WARNING
To prevent SERIOUS INJURY or DEATH from a closing garage door:
- The Photo Eye Safety System MUST be installed BEFORE connecting power.
- The Photo Eye Safety System MUST be properly connected and aligned BEFORE operating the Opener.
