decaWave DW1000 User Manual Download Page 21 | Manualshive

Page: 21 / 242

background image

DW1000 User Manual

© Decawave Ltd 2017

Version 2.12

Page 21 of 242

GPIOs are set to mode 0, their default function as shown in Table 3.

Table 3: GPIO Default Functions

GPIO Pin

Default Function

GPIO0/RXOKLED

GPIO0

GPIO1/SFDLED

GPIO1

GPIO2/RXLED

GPIO2

GPIO3/TXLED

GPIO3

GPIO4/EXTPA

GPIO4

GPIO5/EXTTXE/SPIPHA

GPIO5

GPIO6/EXTRXE/SPIPOL

GPIO6

SYNC/GPIO7

SYNC

IRQ/GPIO8

IRQ

Smart TX power is on by default, see section

Register file: 0x1E – Transmit Power Control

and

Smart Transmit

Power Control

for configuration and operation information.

Sniff mode is off, see

Register file: 0x1D – SNIFF Mode

for details, frame wait timeout (see SYS_CFG register

Register file: 0x0C – Receive Frame Wait Timeout Period

) and preamble detection timeout

(see

Sub-Register 0x27:24 – DRX_PRETOC

) are off, whilst SFD detection timeout (see

Sub-Register 0x27:20 –

) is on.

Other SYS_CFG register settings such as Automatic Receiver Re-Enable (RXAUTR) and MAC functions such as
frame filtering (FFEN), double buffering (DIS_DRXB) and automatic acknowledgement (AUTOACK) are all off
by default. Automatic CRC generation is on and the CRC LFSR is initialized to 0’s (FCS_INIT2F).

Note that CRC generation is selected as part of a transmit command, see

Register file: 0x0D – System Control

External synchronisation and the use of external power amplifiers are deactivated by default, see sections

6.1 – External Synchronisation

and

6.2 – External Power Amplification

2.5.2 Default Channel Configuration

Channel 5, preamble code 4 and 16 MHz PRF are set by default in the CHAN_CTRL register, see

Register file:

0x1F – Channel Control

for more information.

The transmit data rate is set to 6.8 Mbps in the TX_FCTRL register, see TXBR field in

Register file: 0x08 –

Transmit Frame Control

. The receive data rate is never set unless 110 kbps reception is required. Note that

this must be configured in register SYS_CFG, field RXM110K, s ee

Register file: 0x04 – System Configuration

The RF PLL and Clock PLL are configured for channel 5 operation by default, please refer to

Register file: 0x2B

– Frequency synthesiser control block

for channel configuration settings for each channel.

«
...
19
20
21
22
23
...
»

Summary of Contents for DW1000



















































































































































































































































Reviews:

No comments

Related manuals for DW1000

Brand: Accurate Technology Pages: 20

Brand: Harman Kardon Pages: 4

Brand: Harman Kardon Pages: 4

Brand: Harman Kardon Pages: 11

Brand: Harman Kardon Pages: 48

Brand: Harman Kardon Pages: 118

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 10

Brand: Harman Kardon Pages: 52

Brand: MadgeTech Pages: 4

wM-Bus 868 USB Key

Brand: MADD Pages: 4

Brand: M-system Pages: 18

Brand: Strong Pages: 24

vigilantplant EJA Series

Brand: YOKOGAWA Pages: 79

PluraSens E2658-O3

Brand: Evikon Pages: 21

Brand: Kanomax Pages: 27

Brand: M-system Pages: 5

Brand: Yaesu Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands