GHOST 200
Operating instructions and warnings
8
WARNING
To ensure an appropriate level of electrical safety
always keep the 230V power supply cables apart (minimum
4mm in the open or 1 mm through insulation) from low volta-
ge cables (motors power supply, controls, electric locks, aerial
and auxiliary circuits power supply), and fasten the latter with
appropriate clamps near the terminal boards.
WARNING
In line with EU Directive 2002/96/EC for waste
electrical and electronic equipment (WEEE), this electrical
product must not be disposed of as unsorted municipal waste.
Please dispose of this product by returning it to your local mu-
nicipal collection point for recycling.
3 MODELS AND CONTENTS
OF THE PACKAGE
The name GHOST 200 identifies a series of underground
electro-mechanical operators with different features depending
on motor phase power supply and speed.
DEA System articles in the series are listed in the “AVAILABLE
MODELS” table.
GHOST 200 is completed by a set of accessories listed in the
“PRODUCT ACCESSORIES” table.
Inspect the “Contents of the Package” on Page 30 and com-
pare it with your product for useful consultation during assembly.
4 OPERATING INSTRUCTIONS
In compliance with Directive 2006/42/CE Enclosure I, Point
1.7.4.
4.1 Product description
GHOST 200 is an electromechanical operator for swing ga-
tes (see F1, page 30) rotating an articulated arm.
This arm is connected to the gate to be operated by means of
the lever unit of the foundation box. The lever unit, that will be
properly welded at the time of installation, has a built-in opera-
tor unlocking device which will allow you to open the gate even
if there is a power supply failure.
4.2 Technical data
See the “TECHNICAL DATA” table.
4.3 Labelling information
Part of the summarised data for the CE label are listed in the
label applied to the product (see Position F7, Page 32); the data
regarding the seller are found in the enclosed Warranty, whi-
le “Indispensable Operating Safety Elements” are found under
Point “4.2 Technical data”.
4.4 Appropriate conditions of use
The GHOST 200 is designed for installation in civil and indu-
strial swing gates as an actuator for the operational automatism
as shown in F3 on Page 31. By installing the accessory item 216
you may widen the wing angle of opening up to 180°.
The GHOST 200 has been designed and tested for opera-
tion under “normal” civil and industrial gate opening conditions;
temperature limits, degrees of protection against dust and water,
and other data are provided in Point 4.2 “Technical Data”.
Satisfactory operation requires the correct positioning of
the GHOST 200 operator with respect to the gate (see F4 page
30).
The required automation must be selected according to the
gate to be moved; the attrition on the attachments, the weight,
the length/height of the gate wing, and the degree of closing
of the surfaces are the elements to be considered. The chart
“LENGTH-WEIGHT” correlating the length of the gate leaf and
its weight in typical situations can be used in selecting the auto-
mation according to the gate to be automated.
“PRODUCT ACCESSORIES” table
Article
Code
Description
215
629000
Zinc-plated foun-
dation box with
release device
215 I
629010
Stainless steel
foundation box with
release device
216
629020
Device to be in-
stalled on item art.
215 and 215I to
get a 180° angle of
opening
218
629030
Mechanical stop
200 - 200CL - 200/EN - 200/CLEN
200L
200/24 - 200/24CL
Motor power supply voltage (V)
230 V ~ ±10% (50/60 Hz)
24 V
Absorbed power (W)
400
330
150
Max torque (Nm)
320
300
210
Duty cycle (cycles/hour)
20 - 28
(200/EN)
18
40
Maximum n° of operations in 24 hour
200
200
280
Built-in capacitor (µF)
12,5
-
Operating temperature range (°C)
-20÷50 °C
Motor thermal protection (°C)
150 °C
-
Opening time 90° (s)
17
26
16
Weight of product with package (Kg)
14,5
14
Protection degree
IP67
