background image

CONTENTS

Another five detailed, easy-to-follow stages  
in building your Sky Rider Drone. 

Stage   14

:  Straps for the battery case

Stage   15

:  Assembling the body 

Stage   16

:  The first electronic speed control  

Stage   17

:  Back left arm cover

Stage   18:    

Checklist  

TM

www.model-space.com

Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP

 

All rights reserved © 2015
Published in the UK by De Agostini UK Ltd, 

Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE
Published in the USA by De Agostini Publishing USA Inc., 

915 Broadway, Suite 609, New York, NY 10010.
Items may vary from those shown.

Picture credits: p32 Corbis, p33-41 De Agostini, p42 Corbis

Responsibility

De Agostini advises that the use of Sky Rider Drone is subject to all the relevant regulations 

currently in force. Such regulations require the prudent and responsible use of Sky Rider Drone 

at all times, stating the responsibility of the user in the event that the same causes any damage 

or injury to persons or property on the ground or to other users of the airspace in proximity of 

which Sky Rider Drone flies. De Agostini also points out that it is not permitted to use Sky Rider 

Drone for unauthorised or unlawful purposes; if Sky Rider Drone is used for unauthorised or 

unlawful purposes, the user will be fully responsible for any loss or damage arising from such 

unauthorised use. In particular, the user must comply with all provisions of law and refrain from 

using Sky Rider Drone in any manner that could interfere with third-party privacy rights.

De Agostini declines any liability for any damage arising from the use of Sky Rider Drone.

Privacy rights

De Agostini recommends that the use of the built-in camera aboard Sky Rider Drone is in 

accordance with the relevant provisions of law. The recording and disclosure of the image of a 

person without their prior consent may in fact constitute infringement of law and involve the 

responsibility of the author of such actions. De Agostini therefore recommends photographing 

people only with their prior consent and not to use in any way these recordings (for example, by 

storing and/or disseminating them by any means of communication) without first obtaining such 

consent. De Agostini recommends that images likely to harm the reputation or dignity of a person 

are not disclosed.  The use of Sky Rider Drone for purposes of monitoring or spying is strictly 

prohibited and may be punishable by law.

Disclaimer

The explanations and specifications set out in the relevant sections of Sky Rider Drone are 

only for information purposes and are to be considered correct at the time of publication. They 

have been prepared with the utmost attention in order to provide users with accurate and 

reliable information. However, De Agostini cannot be held responsible for any consequences 

arising from omissions and/or errors in these instructions, nor for any damage caused directly 

or indirectly from the use of the information herein contained. Since the commitment of De 

Agostini is designed to ensure continual updates and improvements, the product you have 

purchased may slightly differ from the model described in the instructions.

IMPORTANT INFORMATION   

Not suitable for children under the age of 14. This product is not a toy and is not designed or intended for use in play.

34

Assembly Guide

Summary of Contents for Sky Rider Drone












Reviews: