background image

Model 3770        

DC STRAIN GAGE PANEL METER 

  

Controls

 

Analog Symmetry, + CAL, - CAL, TARE 

S Y M  

Symmetry - 

Adjust the negative gain slope for symmetrical analog adjustment and display 

reading with reference to the positive span value.  20 Turn potentiometer, with approx. ± 2% 
full scale authority 

+ C A L  

Positive  Calibration – 

Activates the SHUNT Positive by switching in the external or internal 

shunt calibration resistor across the Cal Sense and + Sense leads of the bridge.  

- C A L  

Negative  Calibration  – 

Activates the SHUNT Negative  by  switching in the external or 

internal shunt calibration resistor across the Cal Sense and - Sense leads of the bridge.  

TARE 

TARE - 

Push / Push switch. When enabled, offsets the present sensor signal input to "Zero". 

When activated, a green LED light will illuminate. During activation process, LED will light 
Yellow. If disabled, or out of range, LED will be RED. TARE maybe remotely activated via 
rear J1 connections. Front panel TARE can be disabled via J1 Pin 5connected to Logic 
Common, Pin 6. Maximum TARE capability is approx. 60% of full scale reading.

   

Page 

1

4

 

Summary of Contents for 3770P





































Reviews: