background image

DAX66 INSTALLATION — OVERVIEW 

Install the DAX66 in a well-ventilated location; do not block the vents on the sides or top of the chassis, proper ventilation is required for 

normal operation. Do not expose the unit to excessive dust and do not allow dust to build up on the unit and block the vent holes in the 

chassis. Do not place the DAX66 above or below heat-generating components such as another audio amplifier. Be sure to leave at least 

2 inches of space to the sides of the chassis with open air flow above and below the unit. Due to the weight of the unit, we recommend  

 

 

OVERVIEW:

 

1. The DAX66 can be mounted in an equipment rack using the included rack mount kit.  

2. Always disconnect AC power before making connections to the DAX66. 

3. Use good quality 12 or 14 AWG stranded copper speaker wire for all speaker connections. 

4. Use good quality cable for connection of the keypads to the master controller/amplifier; we recommend Cat5e to connect keypads. 

5. The DAX66 uses a keypad hub; all keypads will connect to the hub. Install the keypad hub close to the master controller/amplifier. 

For ease of installation, the keypads and the keypad hub are fitted with quick-disconnect screw terminal blocks. 

6. The keypad hub connects easily to the master controller/amplifier using a standard Ethernet patch cable.  

NOTE:

 When attaching 

a keypad to an electrical 

box, use a screwdriver 

to reduce the chance of 

damage to the keypad. 

NOTE: Set the Address of each keypad using the DIP switches on back of the keypad.

 

ZONE-1

 

ZONE-2

 

ZONE-3

 

ON

 

ZONE-4

 

ZONE-5

 

ZONE-6

 

1  2  3

 

 

1

 

OFF

 

2

 

ON

 

3

 

 

1

 

ON

 

2

 

OFF

 

3

 

 

1

 

ON

 

2

 

ON

 

3

 

ON

 

1

 

 

2

 

OFF

 

3

 

ON

 

1

 

 

2

 

ON

 

3

 

ON

 

1

 

ON

 

2

 

OFF

 

3

 

Each keypad must have a distinct address to communicate correctly with the 

controller/amplifier. Select zone address numbers 1 through 6 by using the chart 

to the right. A DIP switch in the up position is ON; a DIP switch in the down 

position is OFF. 

daytonaudio.com

[email protected]

using four-post racks at minimum.

Summary of Contents for DAX66



















Reviews: