background image

17

Technical Data

This section provides you with the technical specifications for your e-ATV.

The Motor and Wheel Assembly

The Smart ATV has a 800 Watt magnetic DC brushless motor on the rear wheel hub. This type of motor has 

excellent low-end torque and high efficiency when working within its range. Note that while the motor is 

very quiet, it does produce some noise. Also attached to the rear hub are speed reduction gear and the 

speed free clutch.

The Freewheel

The wheels have freewheels, so the e-ATV’s drive train is not fixedly geared. This means that when coasting 

or traveling downhill, you can turn off the engine and your e-ATV will continue to move without slowing. 

This feature will allow you to achieve faster speeds when coasting, moving downhill or moving with the 

wind. It will also allow you to conserve electrical power, because you will be able to let to the motor rest 
while moving.

The Controller

Daymak pioneered the development of intelligent component control in e-ATVs. The “D- Drive” technology 

developed by Daymak is the brain of your e-ATV. It allows your e-ATV to achieve faster acceleration, to climb 

steeper hills, and to save energy. In future, it will allow for other ways of recharging your e-ATV’s batteries, 
such as by using solar or wind power.

The electronic controller is located under the seat assembly. This controller efficiently regulates the speed 

and electronic functions of the ATV. It allows for stepless speed adjustment, shuts off the motor when the 

brakes are activated, has low voltage protection and has fuses to prevent excess current from damaging the 
e-ATV’s systems.

The Governor

A key component of the controller is the Governor. The Governor regulates the speed of the e-ATV. It pre-

vents the motor from assisting riders when the e-ATV’s speed surpasses

32 km per hour.

The governor’s primary function is to make sure that the motor functions efficiently. If the governor is not 

functioning, the mileage of the e-ATV will be dramatically reduced, and its performance will suffer.

Disabling the governor voids the warranty, and may damage your controller.

This speed limitation to 32 km per hour is required by government regulations. Traveling faster than 32 km 

per hour through motor power alone is illegal in Canada and could result in serious fines or penalties, unless 
your vehicle is insured for liability, is registered and you are licensed to drive.

Summary of Contents for Sasquatch 1000W

























Reviews: