background image

Technical Maintenance

The maintenance and operation of the heater should be done in the following cases.

 

»

During commissioning.

 

»

When changing from one type of gas to another.

 

»

After entering storage mode in case of seasonal use, before operating.

 

»

After troubleshooting.

 

»

At least once a year, regardless of the technical situation. 

CAUTION! The person who maintains the heater and checks its operation;

 

»

Read this guide.

 

»

The person who maintains the heaters and controls their operation must have the 

knowledge of 

“Safety Rules for Gas Distribution and Gas Consumption Networks” 

and have a certificate.

 

»

The person who maintains and ensures the operation of the heaters must have 

knowledge of electrical safety.

Performed During Maintenance List of Required Activities

 

»

Make an external inspection to determine the mechanical damage to the device, 

open the intervention paper of the device and make sure that there are no cracks 

or damage.

 

»

Check the condition of the ignition rods for signs of damage from exposure to high 

temperatures.

 

»

Ensure timely replacement of defective parts. Make sure that there are no foreign 

objects that interfere with the operation of the heater.

 

»

Clean the outer surfaces from dust and dirt, wipe the reflective surfaces of the 

reflectors with a dry and soft cloth.

 

»

Clean the inside of the heater by blowing compressed air at a pressure of 0.4-0.5 

MPA through a 3 mm nozzle. Blow through the openings of the tiles from the out-

side, then from the inside through the opening of the mixing tube. Evacuate to run 

until there is no dust exit from the heater. The frequency of cleaning the interior 

depends on the degree of dust in the room.

 

»

Check all electrical connections, check the grounding of the device.

 

»

Check the tightness of all threaded connections of the heater and gas pipeline.

 

»

Check the operation of the gas valve, adjust the gas pressure in front of the burn-

er nozzle if necessary, make sure that both pressure control nipples are tight.

 

»

Check the operation of automation and security systems. Clean the inside of the 

heater by blowing compressed air at a pressure of 0.4-0.5 MPA through a 3 mm 

nozzle.

 

»

Perform the test run of the heater, make sure the device is in good condition.

Attention! In seasonal conditions of use of the heater, in case of long inactivity 

of the device, it is recommended to cover the hole in the mixing tube with cloths 

or to take various measures to prevent the penetration of insects and other 

organic substances.

18

www.daygas.eu

Summary of Contents for LODOS Series





























Reviews: