manualshive.com logo in svg

DAVIS Vantage Pro ISS Retrofit Kit, Installation Instructions Manual, Page: 22 / 24

Share
Download
DAVIS Vantage Pro ISS Retrofit Kit Installation Instructions Manual Download Page 22

Page 22

Installation - ISS with External SIM

Procedure 11. Return the Old SIM to Davis

1.

Please return the old SIM and SIM housing (if you have one), in the Fan-
Aspirated ISS Retrofit Kit shipping box.

2.

Include the shipping paperwork you received with the Retrofit Kit.

3.

Ship to:

Davis Instruments
Attn: Returns
3465 Diablo Ave.
Hayward, CA 94545

Troubleshooting

Please contact Davis Technical Support if you have any questions or if you 
encounter problems installing the Fan-Aspirated ISS Retrofit Kit Retrofit Kit.

Contacting Davis Instruments

(510) 732-7814

 for Technical Support, Monday – Friday, 7:00 a.m. – 5:30 p.m. 

Pacific Time. 

(510) 670-0589 

Fax to Customer Service or Tech Support.

www.davisnet.com

 Copies of User Manuals are available on the “Support” 

page. Watch for FAQs and other updates. Subscribe to Davis’ e-newsletter.

[email protected]

 E-mail to Technical Support.

ISS2 SPARS RetroKit D011.fm  Page 22  Wednesday, April 23, 2003  11:26 AM

Summary of Contents for Vantage Pro ISS Retrofit Kit

























Reviews:

No comments