manualshive.com logo in svg

DAVIS Envoy8X, User Manual, Page: 46 / 48

Share
Download
DAVIS Envoy8X User Manual Download Page 46

42

First In Chain Repeater Troubleshooting

The TX and "STAT" LEDs display two error codes corresponding to first in chain repeater 
communication problems when the repeater is in Test Mode. The "STAT" LED flashes 
numbered error codes in red or yellow. After the error code is displayed by the "STAT" LED, 
the "TX" LED may flash the corresponding transmitter ID associated with the error. Also, it is 
possible for a repeater to display more than one error at a time. The two error codes 
corresponding to first in chain communication errors are:

•

Error 3

 - Can occur if a repeater intended to be first in chain does not have the first in chain 

feature enabled. Because the repeater does not know it is supposed to be first in chain, the 
repeater looks for a previous repeater in the chain. Move the two-pin jumper to the bottom 
two-pins on the first in chain header and retest communication.

•

Error 4

 - Can occur if a repeater (with ID other than A) is intended to be part of a single 

chain of repeaters and is set to be first in chain, or if an intended first in chain repeater 
doesn’t have any Transmitter IDs selected. If you have a single chain topology, make sure 
the first in chain jumper is in the default position and retest communication. If you have a 
multiple chain topology, make sure a Transmitter ID has been selected on the first in chain 
repeater and retest communication.

Note:  Please review all communication issues alongside those regarding first in chain repeaters. See 

“Maintenance and Troubleshooting” on page 34 for more information.

Summary of Contents for Envoy8X

















































Reviews:

No comments