background image

 

Page 6

Large Surge-Protector Shelter

 

M

 

OUNTING

 

 

 

THE

 

 S

 

HELTER

 

The instructions below will show you how to mount the shelter against a wall 
or post, on a small pipe, or on a large pipe.

 

Mounting the Shelter on a Wall or Post

 

Attach the shelter to the mounting surface in the desired location using the lag 
screws and 

 

π

 

” flat washers as shown below.

 

M

 

OUNTING

 

 

 

ON

 

 

 

A

 

 W

 

ALL

 

 

 

OR

 

 P

 

OST

 

Mounting On a Small Pipe

 

Follow the instructions below to mount the shelter onto a pipe with outside 
diameter between 

 

 

” and 1

 

π

 

” (19 mm and 31 mm).

 

1. Hold the rear of the shelter and the 1

 

 

” U-bolt saddles against the pipe and slide the 

ends of the 1

 

 

” U-bolts through the holes in the saddles and shelter so that the 

U-bolts wrap around the pipe as shown below.

2. Secure the shelter using a 

 

π

 

” flat washer and hex nut on each end of the U-bolts.

 

Tighten the hex nuts until the shelter is firmly attached to the pipe.

 

M

 

OUNTING

 

 

 

ON

 

 

 

A

 

 S

 

MALL

 

 P

 

IPE

Summary of Contents for Surge Protector









Reviews: