background image

RAINW

AT

ER

SUPPL

Y

from discharge

of rainwater pum

p

Power to pump vi

a

3 pin socket - plug th

e

rainwater pump in here.

1" BSP 

M

200m

m

200

m

m

TO

TO

ILETS

AND/O

R

LAUNDR

Y

(do not mix/cross-connec

t

with mains water supply

)

* Pressure Limiting Valve

MAINS

WA

TER SUPPL

Y

3/4" BSP 

M

Incoming power

to RainBank

®

via 3 pin plug

3/4" BSP 

M

Stop valv

e

200 Micron ‘Y’ Strainer

recommended but not

supplied.

WHERE MAINS PRESSURE EXCEEDS 900kPa.

A PLV* 

MUST

 BE FITTED TO INLET!

RainBan

k

®

 

MUST

 BE INSTALLE

D

HORIZONTALLY AS ILLUSTRATED

.

Stop valve

20mm hol

e

puMp outsIDe tank 

optIon - close up

24

13

Step 3

 – plumb up your suction 

plumbing ensuring that the lowest point 

in the inlet pipe is at least 200mm below 

the lowest water level and at least 100mm 

above the base of the tank.

Step 4

 – Install the float switch. check 

that the float switch lead (9m long) 

will reach the rainbank

®

. For greater 

distances between your rainwater tank 

and pump, a 10m float switch (top and 

side entry) extension lead (Davey part 

no. 14186) will need to be added. up 

to 4 float switch extension leads can be 

added between the pump and the rainwater 

float switch lead. It is recommended that 

the float switch extension lead/s are in a 

protective cinduit.
the float end should be set up so it can 

fall no lower than 100mm above the level 

of the lowest point in the inlet pipe so the 

pump will always be shut off well before it 

can run dry or draw in air. 

this is secured to the pump suction 

pipe with cable ties.  allow no more than 

100mm of cable between the float and the 

lowest cable tie.

the plug end should be plugged into the 

float switch inlet on the underside of the 

rainbank

®

 unit in step 8.

Step 5

 – align the rainbank

®

 for easy 

fitting to the plumbing.

Step 6

 – connect rainbank

®

 to the 

pump.

Step 7

 – connect rainbank

®

 to the 

plumbing.

Step 8

 – connect all leads.

Step 9

 – test the unit - page 21.

W

ARNING: DO NOT

 FIT

 CHECK V

AL

VES BETWEEN RAINBANK

®

, PUMP

 

AND 

TANK, UNLESS PUMP

 IS 

ABOVE MAXIMUM W

A

TER LEVEL

 OF 

TANK.

IMPORTANT: ALL PIPEWORK AND OUTLET FITTINGS FROM RAINBANK

®

 MUST BE LA-

BELLED TO AS3500. TANK MUST HAVE ISOLATION VALVE FITTED. DO NOT CONNECT WITH 
CRIMPED FITTINGS.

100
100

100
100

C

D

E

F

A

D
E
B

A

D
E
B

Summary of Contents for RainBank mkII



















Reviews: