background image

NSF/ANSI STANDARD 55 CLASS A

C

US

  

System Tested and Certified by

NSF International against NSF/ANSI 

55 for Disinfection Performance, 

Class A

MODELS

System

Flow Rate 

(40mJ/cm

2

 @ 70% UVT) 

UV30-CA

29.9 lpm (7.9 gpm)

UV68-CA

68.1 lpm (18 gpm)

UV30-CA

UV68-CA

Please pass these instructions on to the operator of this equipment.

UV Disinfection System

Installation and 

Operating Instructions

AS/NZS: 3497

See instruction manual for use conditions.

Consultez le manuel d’instructions pour les méthodes d’utilisation. 

This system or component conforms to NSF/ANSI 55 for the disinfection of micro-

biologically contaminated water that meets all other public health standards. The 

system is not intended for the treatment of water that has an obvious contamination 

or intentional source, such as raw sewage, nor is the system intended to convert 

wastewater to microbiologically safe drinking water.

If this system is used for the treatment of untreated surface waters or groundwater 

under the direct influence of surface water, a device found to be in conformance for 

cyst reduction under the appropriate NSF/ANSI standard shall be installed upstream 

of the system.

WARNING /

ADVERTISSEMENT

In the event of a 

system failure, boil 

water prior to use

Dans le cas d’une défaillance du 

système, vous devrez faire bouillir 

l’eau avant consumation.

Ce système est fabriquer de composant qui sont conforme à la norme NSF / ANSI 

55 pour la désinfection de l’eau contaminée par des microorganismes et rencontre 

toutes les autres normes de santé publique. Ce système n’est pas conçu pour le 

traitement de l’eau qui a une contamination bactérienne évidente ou, de façon 

intentionnelle comme des eaux usées, et n’est pas conçu pour transformer des eaux 

usées en eau potable pour la consumation humaine.

Si ce système est utilisé pour le traitement des eaux de surface ou sous terraine 

non traitées ou des eaux souterraines avec une influence directe avec une eau de 

surface, il est nécessaire d’installer un appareil jugé conforme pour la réduction des 

kystes sous la norme NSF / ANSI appropriée en amont du système.

System Tested and Certified by

NSF International against CSA

B483.1 and NSF/ANSI 55

for Disinfection Performance, Class A

Ce Système est certifié par NSF 

International CSA B483.1 et NSF 

/ ANSI55 pour sa performance de 

désinfection class A 

System Tested and Certified by

NSF International against CSA

B483.1 and NSF/ANSI 55

for Disinfection Performance, Class A

Ce Système est certifié par NSF 

International CSA B483.1 et NSF 

/ ANSI55 pour sa performance de 

désinfection class A

C

US

C

US

Summary of Contents for Microlene UV68-CA

























Reviews: