Datatek IP-DSU User Manual Download Page 37

Page: 37 / 48

I P - D S U U s e r ’ s M a n u a l

02/02/08

6 A L A R M S

The following table reflects new alarm types generated by the

IP-DSU

. Alarms are

visible at the console and via StarKeeper® II NMS.

Alarm Text

Severity

Notes

None

N/A

Cold Start trap alarm generated when the
unit starts up

Tx Error on 10BaseT. Check
Physical Connection.

Major

Problem with 10BaseT physical connection

Lost Connectivity to Peer IP-DSU

Minor

Generated when Peer Connectivity is lost;
DCD & CTS is dropped

Peer Connectivity Established

Info

Generated when Peer Connectivity is
established; DCD & CTS is asserted

User Requested Reboot in Progress

Info

Due to manual reboot

Invalid Login Attempt

Minor

Error in login syntax

Invalid Password Change Attempt

Minor

Use of invalid password

Gateway Connectivity Established

Info

ARP Level Connectivity to Router

ICMP Destination Unreachable Msg
Received

Minor

ICMP Destination Unreachable

None

N/A

Trap alarm for SNMP Authorization Failure

SNMP Trap Manager not reachable
(ICMP)

Info

ICMP Destination unreachable on a Trap

Summary of Contents for IP-DSU

















































Search results

Summary of Contents for IP-DSU

Reviews:

Related manuals for IP-DSU

Brands by name

Popular brands

Datatek IP-DSU, User Manual

Search results

Summary of Contents for IP-DSU

Reviews:

Related manuals for IP-DSU

Brands by name

Popular brands